Figure 1 Electromechanical schematic diagram of "shoes" 200mW micropower constant amplitude telegraph transceiver
Component selection
All inductors choose color ring inductors, of which L3 uses 2.2uH at 80 meters. C6 and C7 use 820pF at 80 meters. Transistors Q1 and Q2 have no strict regulations. Silicon NPN transistors with magnification between 100 and 200 can be used normally. For example, 9011, 9013, 9018, 8050, 2N2222A, 2N3904, etc. It is recommended to use 9013 or Q1 for both Q1 and Q2. Both use 2N3904. The crystal must be a fundamental frequency crystal. Both 7.060M and 7.042M crystals are available for sale at the antenna. It is recommended to use sockets on the crystal and L3, C6, C7 on the circuit board to switch the band or frequency. In order to increase the transmission power, you can use a 12V power supply, but you need to increase C10 to about 100u.
Debugging method
Check if there is a short circuit at the end of welding. If not, add a 9V laminated battery, connect the headphones, and do not connect the antenna. Under normal circumstances, you should hear a small "rustle" sound, connect the antenna to increase the noise or you can hear some signals , The current of the whole machine is below 10mA. If you hear a loud howling or excessive current, it means that the circuit is self-excited. The solution is to connect a 103 ceramic capacitor at both ends of "SPEAKER". If it is invalid, connect it in parallel at the 10uF capacitor of the LM386 power filter. If a 103 ceramic capacitor is still invalid, connect a 103 ceramic capacitor in parallel with the 9V power input. The reception should be basically normal by now.
Figure 2 Schematic diagram of the high-frequency power meter with 1W 50 ohm dummy load
Then connect the high-frequency power meter with dummy load (Figure 2 shows the reference circuit diagram), short-circuit the two ends of "KEY", the headset should be silent, and the high-frequency power meter has a certain output. The current of the whole machine is 40-100mA under the launching state. Place a short-wave / medium-wave radio 0.5 meters away from the transmitter to check all the received frequency ranges. Except for the carrier frequency and octave frequency, no other signals generated by "leather shoes" should be heard. If there are other signals (especially howling), there is high-frequency self-excitation. Cut the power line between Q1 and Q2, use 100uH inductance and 100 ohm resistor in parallel and then connect in series to effectively eliminate high-frequency self-excitation. The attached table gives the DC reference voltages of the main components in the transmitting and receiving states.
The basic indicator power supply of this telegraph transmitter: 7V-12V (recommended 9V laminated battery)
Circuit board: 56mm x 41 mm
Antenna: 50 ohms, unbalanced, BNC / Q9 interface LO leakage: about 1mW (on a 50 ohm dummy load)
Frequency range: 7.060-7.064MHz (50p trimmer capacitor connected in series with 7.060M crystal)
receive:
Current: less than 10mA (at 9V power supply)
Headphones: low-resistance headphones (recommended SONY, aiwa and other highly sensitive Walkman headphones)
emission:
Power: about 200mW
Current: about 50mA (at 9V power supply)
Spurious (harmonic) suppression: -20dB
Subjective evaluation of receiving sensitivity and selectivity is poor and susceptible to broadcast interference (BCI). Good frequency stability and high intelligibility when listening to SSB signals. The noise floor of the circuit is small. The switch sound is loud when switching between sending and receiving, which may easily lead to wrong code.
Pet Zipper Braided Sleeve,Expandable Braided Zipper Sleeving Wrap,Pet Side Entry Braided Sleeving With Zipper,Braided Wire Sheathing
Shenzhen Huiyunhai Tech.Co., Ltd. , https://www.cablesleevefactory.com